共找到 205 條與 艙室輔機 相關的標準,共 14 頁
本標準規定了船用油水界面探測器的要求、檢驗方法、檢驗規則、標志、包裝、運輸和貯存。 本標準適用于探測器的設計、制造和驗收。
Require of Marine Oil-water Interface Detector
本標準規定了在溫度為0℃~50℃、濕度為95%的機艙內以電動機驅動的船用立式海水泵(以下簡稱泵)的要求、試驗方法、檢驗規則和標志、包裝、運輸和貯存等。 本標準適用于船舶冷卻系統、壓載系統、消防系統、日用水系統和海水淡化裝置等使用泵的設計、生產與試驗驗收。
Marine vertical sea water pump
本標準規定了船舶自動控制儀表用無油空氣壓縮機的技術要求、試驗方法、檢驗規則以及標志、包裝、運輸和貯存。 本標準適用于額定排氣壓力為0.7 MPa和1 MPa,容積流量最大為360 m/h的空壓機的設計、制造、試驗和驗收等。
Marine oil-free air compressor for control use-Technical specification
本標準規定了潛水裝具用高壓活塞空氣壓縮機的技術要求、試驗方法、檢驗規則以及標志、包裝、運輸和貯存。 本標準適用于潛水作業人員呼吸用的額定排氣壓力為15MPa以上(含15MPa)的空壓機的設計、制造、試驗和驗收等。
Air compressor for high pressure reciprocating air diving apparatus
This standard is a guide for the design, construction, installation, operation, and control of electric bilge pump systems.
Electric Bilge Pump Systems
1.1 This specification covers mechanical end-face seals for centrifugal and positive displacement pumps for shipboard use. 1.2 The following types of seals are not included in this specification: lip seals, oil seals, circumferential seals, or labyrinth seals. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. A companion hard metric standard is in the process of preparation. 1.4 Special requirements for U.S. Navy Shipboard Pump Applications are included in Supplement S1.
Standard Specification for Mechanical Seals for Shipboard Pump Applications
1.1 This specification covers the requirements applicable to the design and construction of centrifugal pumps for shipboard application. The three classes of service covered by this specification are as follows: 1.1.1 Class 1—Freshwater, 1.1.2 Class 2—Seawater, and 1.1.3 Class 3—Hydrocarbon pumps (less than 1500 SSU). 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.
Standard Specification for Centrifugal Pump, Shipboard Use
Surface ship mooring and sea test procedures part 166: Air compressor and compressed air system test
Surface ship mooring and sailing test procedures part 145: Ventilation system test
Surface ship mooring and sailing test procedures part 146: air conditioning system test
Surface ship mooring and sailing test procedures part 147: Refrigeration system test
Specification For Sealless Lube Oil Pump With Oil Through Motor For Marine Applications
Ships and marine technology - Air-conditioning and ventilation of accommodation spaces - Design conditions and basis of calculations; Technical Corrigendum 1
Ships and marine technology - Air-conditioning and ventilation of accommodation spaces - Design conditions and basis of calculations; Technical Corrigendum 1
Specifies requirements for pumping or alternative means designed to remove normal accumulations of bilge water for small craft with a hull length of up to 24 m. Does not set requirements for bilge pumps or bilge-pumping systems designed for damage contro
Small craft - Bilge-pumping systems
本標準規定了了船用碟式分離機模塊(以下簡稱模塊)的分類和標記、要求、試驗方法、檢驗規則及標志、包裝、運輸和貯存。 本標準適用于船舶燃油、滑油模塊的設計、制造和檢驗。
Disc separator module
This specification defines the requirements applicable to design and construction of rotary positive displacement pumps for shipboard use. The classes of service are shown in Section 4. This specification will not include pumps for hydraulic service or cargo unloading applications.
Specification for Rotary Positive Displacement Pumps, Commercial Ships Use
1.1 This specification defines the requirements applicable to design and construction of rotary positive displacement pumps for shipboard use. The classes of service are shown in Section 4. 1.2 This specification will not include pumps for hydraulic service or cargo unloading applications.
Standard Specification for Rotary Positive Displacement Pumps, Ships Use
本規范規定了艦船用離心泵機械密封的要求、質量保證規定、交貨準備等。 本規范適用于艦船用離心泵、旋渦泵及其它類似泵的機械密封。
Specification of mechanical seal for centrifugal pump on ships
? ??? ??? ??? ???? ?? ??? ? ?? ???(?? ???? ??.)?
Ships-Tachometer for engine
Marine use filters, strainers and separators
Marine use filters, strainers and separators
Copyright ?2007-2025 ANTPEDIA, All Rights Reserved
京ICP備07018254號 京公網安備1101085018 電信與信息服務業務經營許可證:京ICP證110310號
頁面更新時間: 2025-06-06 11:25